FoamFit Tools section divider

Foam Tool Organizer for
166 Craftsman Inch and Metric Sockets

see all organizers for sockets

Overview

166 Craftsman Inch and Metric Sockets

Fits (50) 1/4-drive sockets,
(81) 3/8-drive sockets,
and (35) 1/2-drive sockets.

Accommodates all sockets from the 298-piece mechanics set CMMT12039.

Caution: Recommended for a 3-3/4 inch or deeper drawer.

New!

Drawer Size
22-1/4 X 16-1/4 inches

$57.25



FoamFit Tools section divider

Details

This foam tool organizer is made from closed-cell polyethylene tool foam. It has been precision CNC-cut to fit the following 166 Craftsman sockets:

(11) 1/4-drive 6-point sizes from 5/32 to 9/16
(10) 1/4-drive 6-point deep sizes from 5/32 to 9/16
(13) 1/4-drive 6-point sizes from 4 to 14 mm
(3) 1/4-drive torx bits from T15 to T25
(13) 1/4-drive 6-point deep sizes from 4 to 14 mm
(13) 3/8-drive 6-point sizes from 1/4 to 1
(11) 3/8-drive 6-point deep sizes from 1/4 to 7/8
(17) 3/8-drive 6-point sizes from 6 to 22 mm
(15) 3/8-drive 6-point deep sizes from 6 to 19, 21 mm
(3) 3/8-drive spark plug socket sizes 13/16, 3/4, 5/8
(3) 3/8-drive phillips bits
(3) 3/8-drive slotted bits
(6) 3/8-drive inch hex bits from 5/32 to 3/8
(6) 3/8-drive metric hex bits from 4 to 10
(4) 3/8-drive torx bits from T30 to T50
(11) 1/2-drive 12-point sizes from 3/8 to 1
(6) 1/2-drive 12-point deep sizes from 3/8 to 3/4
(10) 1/2-drive 12-point sizes from 13 to 24 mm
(6) 1/2-drive 12-point deep sizes from 14 to 19 mm
(2) 1/2-drive hex bits 14 and 17 mm

This tool organizer was designed to fit all the sockets from the Craftsman 298-piece set CMMT12039.

This organizer is designed to fit a toolbox drawer with inner dimensions of:

22-1/4 X 16-1/4 inches
(inside width by inside length)

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.



Made in the USA!

Foam Organizer for all Sockets From Craftsman 298-pc Mechanics Tool Set

Note: tools are not included

FoamFit Tools section divider

Drawing

Please verify this organizer fits your tools before placing an order.

  1. Download the drawing: www.FoamFitTools.com/product/F-03102-T.pdf
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider