FoamFit Tools section divider

Foam Tool Organizer for
48 Tekton 1/4-drive Sockets with 6 Drive Tools and 11 Nut Drivers

see all organizers for Tekton tools

Overview

48 Tekton 1/4-drive Sockets with 6 Drive Tools and 11 Nut Drivers

Fits (22) inch sockets, (26) metric sockets, 1/4-drive ratchet, (5) drive tools, (6) inch nut drivers, and (5) metric nut drivers.

Accommodates the 1/4-drive sockets and drive tools (minus case) from the Tekton 55-pc set SKT05301, plus the nut drivers from sets DHD91101 and DHD91201.

Only fits the older version of the 1/4-drive set with the red spinner handle.

Drawer Size
23-3/4 X 17-3/4 inches

$59.90



FoamFit Tools section divider

Details

sockets:
(11) 1/4-drive deep 6-point sizes from 5/32 to 9/16
(11) 1/4-drive 6-point sizes from 5/32 to 9/16
(13) 1/4-drive deep 6-point sizes from 4 to 14 mm
(13) 1/4-drive 6-point sizes from 4 to 14 mm

drive tools:
1/4-drive 90-tooth quick-release ratchet
1/4-drive 6-inch spinner handle (with red handle)
1/4 X 3 extension
1/4 X 6 extension
1/4 universal joint
1/4-drive hex bit holder

inch nut drivers:
3/16 (Tekton 26862)
1/4 (Tekton 26863)
5/16 (Tekton 26864)
3/8 (Tekton 26866)
7/16 (Tekton 26867)
1/2 (Tekton 26868)

metric nut drivers:
6mm (Tekton 26884)
7mm (Tekton 26885)
8mm (Tekton 26886)
9mm (Tekton 26887)
10mm (Tekton 26888)

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.



Made in the USA!

Foam Organizer for 48 Tekton 1/4-drive Sockets with 11 Nut Drivers and 6 Drive Tools

note: tools are not included

Tool Requirements

This tool organizer was designed to fit the 1/4-drive sockets, ratchet, and drive tools from the Tekton 55-pc set SKT05301. It fits the older version with the red spinner handle. It also fits the Tekton High-Torque nut drivers from the 6-pc inch set DHD91101 and the 5-pc metric set DHD91201.

Possible Modifications

Minimum trimmable size:

21-3/4 X 15-13/16 inches

Note: Trimmed organizers are not returnable.

Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.

Colors by special request:

black/yellow, black/green, black/gray

Contact customer service to order this organizer in a special color.

Drawing

Please verify this organizer fits your tools before placing an order.

  1. Download the drawing: www.FoamFitTools.com/product/F-04661-R.pdf
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site