FoamFit Tools section divider

Foam Tool Organizer for
9 Channellock Pliers with Snips and 2 Klein Wire Strippers

see all organizers for Channellock tools

Overview

9 Channellock Pliers with Snips and 2 Klein Wire Strippers

Fits (8) Channellock pliers, (1) adjustable wrench, (1) tin snips, and (2) Klein wire strippers.

May be trimmed to fit a variety of drawer sizes.

New!

Drawer Size
23-3/4 X 17-3/4 inches

$56.40



FoamFit Tools section divider

Details

This foam tool organizer is made from closed-cell polyethylene tool foam. It has been precision CNC-cut to fit the following 12 Channellock and Klein tools:

9-1/2 crimping pliers (Channellock 909)
7-inch cutting (diagonal) pliers (Channellock 337)
7-1/8 wire stripper and cutter, 10-18 AWG solid (Klein 11055)
7-1/8 wire stripper and cutter, 20-30 AWG solid (Klein 11057)
8-inch retaining ring pliers (Channellock 927)
10-inch tin snips (Channellock 610TS)
8-inch adjustable wrench, 1-1/2 inch capacity (Channellock 8WCB)
6-inch long nose pliers (Channellock E326)
8-inch long nose pliers (Channellock E318)
6.5-inch slip joint pliers (Channellock 526)
6-1/2 tongue and groove pliers (Channellock 426)
9-1/2 tongue and groove pliers (Channellock 420)

This tool organizer insert may be trimmed to fit a variety of drawer sizes. The minimum size is marked on the drawing (see link below).

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.



Made in the USA!

Foam Organizer for 10 Channellock Tools and 2 Klein Wire Strippers

note: tools are not included

Drawer Size

This organizer is designed to fit a toolbox drawer with inner dimensions of:

23-3/4 X 17-3/4 inches (inside width by inside depth)

It is possible to trim this organizer to fit a smaller drawer. The minimum recommended size is 20-9/16 X 16 inches. Note that trimmed organizers are not returnable. Also, contact customer service to order an organizer trimmed or made with a different sheet size.

Drawing

Please verify this organizer fits your tools before placing an order.

  1. Download the drawing: www.FoamFitTools.com/product/F-04606-R.pdf
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site