Fits (16) inch pass-thru sockets, (16) metric pass-thru sockets, (2) pass-thru ratchets, (2) extensions, and (67) additional tools.
Accommodates all pass-thru sockets and drive tools from the Husky 505-pc set H505MTSPO.
Recommended for 2-1/2 min drawer height.
Drawer Size
12-1/8 X 19-1/2 inches
$54.60
larger image
note: tools are not included
Precision CNC-cut to fit 32 Husky sockets and other tools:
(9) 1/4-drive 6-point pass-through sizes from 5/32 to 1/2
(8) 1/4-drive 6-point pass-through sizes from 4 to 11
(7) 3/8-drive 6-point pass-through sizes from 3/8 to 3/4
(8) 3/8-drive 6-point pass-through sizes from 10 to 17
1/4-drive pass-through ratchet
3/8-drive pass-through ratchet
1/4-drive pass through X 3 extension
3/8-drive pass through X 3 extension
magnetic bit handle
1/4 X 5/16 double box-end ratcheting wrench
5/16 male hex to 1/4-drive socket adapter
1/4-drive pass-through bit adapter socket
3/8-drive pass-through bit adapter socket
(4) phillips screwdriver bit sizes from #1 to #4
(4) slotted screwdriver bit sizes from 1/8 to 5/16
(5) slotted screwdriver bit sizes from 3 to 6.5mm
(6) hex screwdriver bit sizes from 1/8 to 5/16
(8) hex screwdriver bit sizes from 2.5 to 8 plus 10mm
(3) square screwdriver bit sizes from #0 to #2
(4) pozi screwdriver bit sizes from #1 to #4
(8) torx screwdriver bit sizes from T10 to T45
(8) tamper torx screwdriver bit sizes from T10 to T45
(6) nut driver bit sizes from 1/4 to 1/2
(6) nut driver bit sizes 6 and 8 to 12mm
This tool organizer was designed to fit the pass-thru sockets and drive tools from the Husky 505-pc set H505MTSPO plus the screwdriver bits and related tools.
Printing the drawing at 100% scale can be an easy way to check if your tools will fit. Our drawings have multiple pages which can be printed on letter-size paper. Always change the printer setting from "fit" to 100%. If the border prints slightly too small, it is often due to this setting.
12-1/8 X 19-1/2 inches (inside width by inside depth)
Recommended for a drawer with at least 2-1/2 inches of vertical clearance.
It is possible to trim the margins to fit a smaller drawer. Trimmed tool organizers are not returnable. The minimum recommended size is:
11-5/8 X 15-11/16 inches
Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.
We make these colors in smaller batches, but they are often in stock. Contact customer service to order.
Each FoamFit insert is designed for shadowing a specific brand and set of tools. These organizers are made from high-quality tool foam with pockets precision-cut on our CNC routers.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. The foam is resistant to most oils and fuels.