Home |
About |
FAQ |
Shipping Policies |
Extras and Deals |
Custom Options |
Contact Us
22-pc Tekton High-Torque Screwdriver Set
Fits (8) slotted, (8) phillips, and (6) torx screwdrivers from 22-pc sets DRV41219 or DRV43009.
May be trimmed to fit a variety of drawer sizes.
Only fits Tekton high-torque screwdrivers. Does not fit the red, hard-handle screwdrivers.
Drawer Size
23-3/4 X 17-3/4 inches
$56.40
This foam tool organizer is made from closed-cell polyethylene tool foam. It has been precision CNC-cut to fit the following 22 Tekton screwdrivers:
slotted:
1/4 X 1-1/2 (Tekton 26621 or DHS30250)
1/8 X 4 (Tekton 26603 or DHS31125)
3/16 X 4 (Tekton 26613 or DHS31188)
1/4 X 4 (Tekton 26623 or DHS31250)
5/16 X 4 (Tekton 26633 or DHS31313)
3/16 X 8 (Tekton 26615 or DHS34188)
1/4 X 8 (Tekton 26625 or DHS34250)
5/16 X 8 (Tekton 26635 or DHS34313)
Phillips:
#2 X 1-1/2 (Tekton 26671 or DHP30002)
#0 X 4 (Tekton 26653 or DHP31000)
#1 X 4 (Tekton 26663 or DHP31001)
#2 X 4 (Tekton 26673 or DHP31002)
#3 X 4 (Tekton 26683 or DHP31003)
#1 X 8 (Tekton 26665 or DHP34001)
#2 X 8 (Tekton 26675 or DHP34002)
#3 X 8 (Tekton 26685 or DHP34003)
Torx:
T10 X 4 (Tekton 26801 or DHT31100)
T15 X 4 (Tekton 26802 or DHT31150)
T20 X 4 (Tekton 26803 or DHT31200)
T25 X 4 (Tekton 26804 or DHT31250)
T27 X 4 (Tekton 26805 or DHT31270)
T30 X 4 (Tekton 26806 or DHT31300)
This organizer was designed to fit the 22 Tekton High-Torque screwdrivers from black oxide set DRV41219 or chrome set DRV43009. It fits the larger, nonslip handles that Tekton calls High-Torque.
23-3/4 X 17-3/4 inches (inside width by inside depth)
It is possible to trim this organizer to fit a smaller drawer. The minimum recommended size is 21-3/4 X 16 inches. Note that trimmed organizers are not returnable. Also, contact customer service to order an organizer trimmed or made with a different sheet size.
Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.