Contact Us |
Drawing and Part Number Lookup
920-569-0140
Foam Tool Organizer for
25 GearWrench Metric Combination Wrenches
Overview
25 GearWrench Metric Combination Wrenches
Fits (25) metric combination wrenches from 6 to 32 mm.
Accommodates the metric combination wrenches from the GearWrench 44-pc set 81919.
Caution: Recommended for a 3-1/8 inch or taller drawer.
May be trimmed to fit a variety of drawer sizes.
Drawer Size
24 X 18 inches
$79.70
Details
- Drawer size: 24 X 18 inches (inside width by inside depth)
- Standard colors: black/red, blue/yellow, black/blue
- Made from closed-cell polyethylene tool foam.
- Precision CNC-cut to fit 25 GearWrench wrenches:
metric combination sizes:
6 mm (GearWrench 81736)
7 mm (GearWrench 81737)
8 mm (GearWrench 81665)
9 mm (GearWrench 81666)
10 mm (GearWrench 81667)
11 mm (GearWrench 81668)
12 mm (GearWrench 81669)
13 mm (GearWrench 81670)
14 mm (GearWrench 81671)
15 mm (GearWrench 81672)
16 mm (GearWrench 81673)
17 mm (GearWrench 81674)
18 mm (GearWrench 81675)
19 mm (GearWrench 81676)
20 mm (GearWrench 81677)
21 mm (GearWrench 81678)
22 mm (GearWrench 81679)
23 mm (GearWrench 81741)
24 mm (GearWrench 81742)
25 mm (GearWrench 81751)
26 mm (GearWrench 81752)
27 mm (GearWrench 81743)
28 mm (GearWrench 81753)
30 mm (GearWrench 81744)
32 mm (GearWrench 81745D)
Free shipping on all orders within the contiguous 48 US states.
Made in the USA!
note: tools are not included
Tool Requirements
This tool organizer was designed to fit the metric combination wrenches from GearWrench set 81919.
Possible Modifications
Minimum trimmable size:
21-3/16 X 15-3/4 inches
Note: Trimmed organizers are not returnable.
Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.
Colors by special request:
black/yellow, black/green, black/gray
contact customer service to order this organizer in a special color.
Drawing
Please verify this organizer fits your tools before placing an order.
- Download the drawing: www.FoamFitTools.com/product/F-04179-T.pdf
- Print the pages of the drawing full size or 100% (not fit).
- Check that the printout is full size by measuring the border with a ruler.
- Assemble the pages and place the printed drawing in your toolbox drawer.
- Place the tools over the printed outlines. Visually check that each tool fits within its outline.
Additional Information
Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.
