FoamFit Tools section divider

Foam Tool Organizer for
19 GearWrench Inch Combination Wrenches

see all organizers for GearWrench tools


19 GearWrench Inch Combination Wrenches

Fits (19) inch combination wrenches from 1/4 to 1-1/2.

Accommodates the inch combination wrenches from the GearWrench 44-pc set 81919.

Caution: Recommended for a 3-9/16 inch or taller drawer.

May be trimmed to fit a variety of drawer sizes.


Drawer Size
24 X 18 inches


FoamFit Tools section divider


This foam tool organizer is made from closed-cell polyethylene tool foam. It has been precision CNC-cut to fit the following 19 GearWrench wrenches:

inch combination sizes:
1/4 (GearWrench 81650)
5/16 (GearWrench 81652D)
11/32 (GearWrench 81653)
3/8 (GearWrench 81654)
7/16 (GearWrench 81655)
1/2 (GearWrench 81656)
9/16 (GearWrench 81657)
5/8 (GearWrench 81658)
11/16 (GearWrench 81659)
3/4 (GearWrench 81660)
13/16 (GearWrench 81661)
7/8 (GearWrench 81662)
15/16 (GearWrench 81663)
1 (GearWrench 81664)
1-1/16 (GearWrench 81733)
1-1/8 (GearWrench 81734)
1-1/4 (GearWrench 81735)
1-5/16 (GearWrench 81749)
1-1/2 (GearWrench 81750)

This tool organizer was designed to fit the inch combination wrenches from GearWrench set 81919.

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.

Made in the USA!

Foam Organizer for 19 GearWrench Inch Combination Wrenches

note: tools are not included

Drawer Size

This organizer is designed to fit a toolbox drawer with inner dimensions of:

24 X 18 inches (inside width by inside depth)

It is possible to trim this organizer to fit a smaller drawer. The minimum recommended size is 21 X 14-1/4 inches. Note that trimmed organizers are not returnable. Also, contact customer service to order an organizer trimmed or made with a different sheet size.


Please verify this organizer fits your tools before placing an order.

  1. Download the drawing:
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site