79 Craftsman 1/4-drive Sockets with 141 Additional Tools
Fits (37) inch sockets, (42) metric sockets, (120) bits, and (21) other tools.
Accommodates the 1/4-drive sockets, drive tools, screwdriver bits from Craftsman 543-pc set CMMT 72000.
22-1/4 X 14-1/2 inches
This foam tool organizer is made from closed-cell polyethylene tool foam. It has been precision CNC-cut to fit the following 220 Craftsman tools:
(5) 1/4-drive 6-point sizes 1/2, 7/16, 3/8, 11/32, and 5/16
(10) 1/4-drive 6-point sizes from 5/32 to 9/16 (skips 9/32)
(11) 1/4-drive 6-point sizes from 5/32 to 9/16 (includes 9/32)
(11) 1/4-drive 6-point deep sizes from 5/32 to 9/16
(5) 1/4-drive 6-point sizes 8, 10, 12, 13, 14 mm
(11) 1/4-drive 6-point sizes from 4 to 14 mm
(13) 1/4-drive 6-point sizes from 4 to 14 mm, including 4.5 and 5.5
(13) 1/4-drive 6-point deep sizes from 4 to 14 mm, including 4.5 and 5.5
(3) 1/4-drive 72-tooth ratchets (Craftsman CMMT81747)
(1) 1/4 X 1-1/2 extension (Craftsman CMMT43538)
(4) 1/4 X 3 extensions (Craftsman CMMT43539)
(2) 1/4 X 6 extensions (Craftsman CMMT43531)
(1) 1/4 X 14 extension (Craftsman CMMT43532)
(2) 1/4-drive universal joints (Craftsman CMMT99216)
(1) 1/4 to 3/8 adapter (Craftsman CMMT13030)
(2) 1/4 to 1/4 hex adapters (Craftsman CMMT81-872)
1/4 ratcheting wrench (Craftsman CMMT39230)
1/4 hex to 1/4 adapter
magnetic handle (Craftsman CMHT65079)
ratcheting magnetic handle
(112) screwdriver bits
(8) metric nut driver bits from 4 to 11 mm
magnet (Craftsman CMMT98316)
This tool organizer was designed to fit all the 1/4-drive sockets and drive tools from the Craftsman 543-pc set CMMT72000. This newer generation of Craftsman tools (mostly made in Taiwan) has a pattern of diagonal markings on the ratchets. Most of the tools are stamped with part numbers that begin with CMMT.
22-1/4 X 14-1/2 inches (inside width by inside depth)
It is possible to trim this organizer to fit a smaller drawer. The minimum recommended size is 21-5/8 X 14-5/16 inches. Note that trimmed organizers are not returnable. Also, contact customer service to order an organizer trimmed or made with a different sheet size.
Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.