FoamFit Tools section divider

Foam Tool Organizer for
31 Husky Metric Crow Foot, Midget, Box End, and Flare-Nut Wrenches

see all organizers for Husky tools

Overview

31 Husky Metric Crow Foot, Midget, Box End, and Flare-Nut Wrenches

Fits (10) crow foot wrenches, (6) flare-nut wrenches, (10) midget wrenches, and (5) deep-offset box wrenches.

Accommodates the metric crow foot, flare-nut, midget, and box end wrenches from the Husky 1025-pc set H1025MTS.

Drawer Size
14-15/16 X 19-3/4 inches

$43.80



FoamFit Tools section divider

Details

This foam tool organizer is made from closed-cell polyethylene tool foam. It has been precision CNC-cut to fit the following 31 Husky wrenches:

crow foot wrenches:
3/8-drive 10 mm
3/8-drive 11 mm
3/8-drive 12 mm
3/8-drive 13 mm
3/8-drive 14 mm
3/8-drive 15 mm
3/8-drive 16 mm
3/8-drive 17 mm
3/8-drive 18 mm
3/8-drive 19 mm

flare-nut wrenches:
9 X 11 (HFNW911MM)
10 X 12 (HFNW1012MM)
13 X 14 (HFNW1314MM)
15 X 17
16 X 18
19 X 21

midget wrenches:
4 mm
4.5 mm
5 mm
5.5 mm
6 mm
7 mm
8 mm
9 mm
10 mm
11 mm

metric box end wrenches:
8 X 10
10 X 12
11 X 13
12 X 14
17 X 19

This tool organizer was designed to fit the metric crow foot, midget, box end, and flare-nut wrenches from the Husky 1025-pc set H1025MTS.

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.



Made in the USA!

Foam Organizer for 31 Husky Metric Crow Foot, Midget, Box End, and Flare-Nut Wrenches

note: tools are not included

Drawer Size

This organizer is designed to fit a toolbox drawer with inner dimensions of:

14-15/16 X 19-3/4 inches (inside width by inside depth)

It is possible to trim this organizer to fit a smaller drawer. The minimum recommended size is 14-7/16 X 19-3/8 inches. Note that trimmed organizers are not returnable. Also, contact customer service to order an organizer trimmed or made with a different sheet size.

Drawing

Please verify this organizer fits your tools before placing an order.

  1. Download the drawing: www.FoamFitTools.com/product/F-03924-R.pdf
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site