FoamFit Tools section divider

Foam Tool Organizer for
20 Husky Drive Tools with 2 Ratchets and 15 Long Hex Bit Sockets

see all organizers for Husky tools


20 Husky Drive Tools with 2 Ratchets and 15 Long Hex Bit Sockets

Fits (2) flex head ratchets, (2) palm ratchets, (13) extensions, (15) Long Hex Bit Sockets, (1) spinner handle, (3) breaker bars, and (1) T-handle.

Accommodates 22 drive tools and 15 hex sockets from the Husky 815-pc set H815MTS.


Drawer Size
31-7/8 X 18-1/2 inches


FoamFit Tools section divider


This foam tool organizer is made from closed-cell polyethylene tool foam. It has been precision CNC-cut to fit the following 22 Husky drive tools and 15 hex sockets:

drive tools:
1/4-drive breaker bar
1/4-drive 2 inch extension
1/4-drive 3 inch extension
1/4-drive 6 inch extension
1/4-drive spinner handle
1/4-drive palm ratchet
3/8-drive flex head ratchet
3/8-drive palm ratchet
3/8-drive breaker bar
3/8-drive 1-1/2 inch extension
3/8-drive 3 inch extension
3/8-drive 6 inch extension
3/8-drive 8 inch flex extension
3/8-drive 10 inch extension
3/8-drive 20 inch extension
1/2-drive flex head ratchet
1/2-drive 14 inch breaker bar
1/2-drive T-handle
1/2-drive 3 inch extension
1/2-drive 5 inch extension
1/2-drive 10 inch extension
1/2-drive 20 inch extension

long ball hex sockets:
(7) 3/8-drive hex socket sizes from 1/8 to 3/8
(8) 3/8-drive hex socket sizes from 3 to 10 mm

This tool organizer was designed to fit the chrome flex head, palm ratchet, extensions, breaker bars, and other drive tools from the Husky 815-pc set H815MTS.

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.

Made in the USA!

Foam Organizer for 4 Husky Ratchets, 13 Extensions, 3 Breaker Bars, T-handle, Spinner Handle, and 15 Long Hex Ball Sockets

note: tools are not included

Drawer Size

This organizer is designed to fit a toolbox drawer with inner dimensions of:

31-7/8 X 18-1/2 inches (inside width by inside depth)

It is possible to trim this organizer to fit a smaller drawer. The minimum recommended size is 30-7/8 X 16 inches. Note that trimmed organizers are not returnable. Also, contact customer service to order an organizer trimmed or made with a different sheet size.


Please verify this organizer fits your tools before placing an order.

  1. Download the drawing:
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site