FoamFit Tools section divider

Foam Tool Organizer for
6 Craftsman Pliers and 8 Soft-Handle Screwdrivers

see all organizers for Craftsman Pliers

Overview

6 Craftsman Pliers and 8 Soft-Handle Screwdrivers

Fits (6) pliers, (4) slotted screwdrivers, and (4) phillips screwdrivers.

Accommodates the screwdrivers from 8-pc set CMHT65075.

Only fits the balck and red handle tools sold by Lowes and other Craftsman dealers starting mid 2018.

Does not fit the black and red handle screwdrivers or TruGrip pliers sold by Sears.

New!

Drawer Size
22-1/4 X 14-1/2 inches

$43.00



FoamFit Tools section divider

Details

This foam tool organizer is made from closed-cell polyethylene tool foam. It has been precision CNC-cut to fit the following 14 Craftsman tools:

slotted screwdrivers:
3/16 X 4 (Craftsman CMHT65061)
1/4 X 1-1/2 (Craftsman CMHT65058)
1/4 X 4 (Craftsman CMHT65059)
5/16 X 6 (Craftsman CMHT65063)

Phillips screwdrivers:
P1 X 3 (Craftsman CMHT65052)
P2 X 1-1/2 (Craftsman CMHT65053)
P2 X 4 (Craftsman CMHT65054)
P3 X 6 (Craftsman CMHT65057)

pliers:
6-in. slip joint pliers (Craftsman CMHT81712)
7-in. diagonal cutter (Craftsman CMHT81647)
8-in. long nose pliers (Craftsman CMHT81645)
8-in. 5-in-one pliers (Craftsman CMHT81715)
10-in. tongue and groove pliers (Craftsman CMHT81720)
10-in. curved jaw locking pliers (Craftsman CMHT81726)

This tool organizer was designed to fit the 8-pc Craftsman soft-handle (bi-material) screwdriver set (CMHT65075), plus 6 individual pliers.

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.



Made in the USA!

Foam Organizer for 6 Pliers and 8 Bi-Material Screwdrivers.

note: tools are not included

Drawer Size

This organizer is designed to fit a toolbox drawer with inner dimensions of:

22-1/4 X 14-1/2 inches (inside width by inside depth)

It is possible to trim this organizer to fit a smaller drawer. The minimum recommended size is 21-3/4 X 14 inches. Note that trimmed organizers are not returnable. Also, contact customer service to order an organizer trimmed or made with a different sheet size.

Drawing

Please verify this organizer fits your tools before placing an order.

  1. Download the drawing: www.FoamFitTools.com/product/F-03881-R.pdf
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site