FoamFit Tools section divider

Foam Tool Organizer for
11 Channellock Pliers, 1 Adjustable Wrench and 12 Wright Screwdrivers

see all organizers for Channellock tools

Overview

11 Channellock Pliers, 1 Adjustable Wrench and 12 Wright Screwdrivers

Fits (6) slotted screwdrivers, (6) Phillips screwdrivers, (11) Channellock pliers, and (1) adjustable wrench.

Caution: older versions of the E326 and E318 long nose pliers may not fit.

New!

Drawer Size
36-1/2 X 16-1/4 inches

$76.20



FoamFit Tools section divider

Details

This foam tool organizer is made from closed-cell polyethylene tool foam. It has been precision CNC-cut to fit the following 24 Wright tools:

Slotted screwdrivers:
1/8 X 3 (Wright 9112)
3/16 X 4 (Wright 9115)
1/4 X 1-1/2 (Wright 9122)
1/4 X 6 (Wright 9124)
5/16 X 6 (Wright 9125)
3/8 X 8 (Wright 9135)

Phillips screwdrivers:
P0 X 3 (Wright 9103)
P1 X 3 (Wright 9104)
P2 X 1-1/2 (Wright 9101)
P2 X 4 (Wright 9105)
P2 X 8 (Wright 9108)
P3 X 6 (Wright 9106)

Pliers:
9.5-inch crimping pliers (Channellock 909)
7-inch cutting (diagonal) pliers (Channellock 437)
7.5-inch lineman's pliers (Channellock 367)
6.5-inch slip joint pliers (Channellock 526)
6-inch long nose pliers (Channellock E326)
8-inch long nose pliers (Channellock E318)
8-inch bent nose pliers with cutter (Channellock E388)
8-inch long reach (duckbill) pliers (Channellock 718)
9.5-inch tongue and groove pliers (Channellock 420)
7-inch wire stripper for 10-20 AWG (Channellock 957)
8-inch retaining ring pliers (Channellock 927)

8-inch adjustable wrench, 1.5-inch capacity (Channellock 8WCB)

The screwdrivers and pliers for this organizer are not sold as a set. Contact Customer Service if you need help finding any of the tools.

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.



Made in the USA!

Foam Organizer for 12 Wright Screwdrivers, 11 Channellock Pliers and 1 Channellock Adjustable Wrench

note: tools are not included

Drawer Size

This organizer is designed to fit a toolbox drawer with inner dimensions of:

36-1/2 X 16-1/4 inches (inside width by inside depth)

It is possible to trim this organizer to fit a smaller drawer. The minimum recommended size is 35-3/4 X 15-3/4 inches. Note that trimmed organizers are not returnable. Also, contact customer service to order an organizer trimmed or made with a different sheet size.

Drawing

Please verify this organizer fits your tools before placing an order.

  1. Download the drawing: www.FoamFitTools.com/product/F-03810-R.pdf
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site