Fits (8) slotted, (8) phillips, and (6) torx screwdrivers.
Accommodates the Tekton screwdrivers with red handles.
Only fits earlier versions where the 1/8 and P0 screwdrivers have 4-inch long handles.
Drawer Size
24 X 18 inches
$59.90
larger image
note: tools are not included
Precision CNC-cut to fit 22 Tekton screwdrivers:
slotted:
1/4 X 1-1/2 (Tekton 30250 or 10250)
1/8 X 4 (Tekton 31125 or 11125)
3/16 X 4 (Tekton 31188 or 11188)
1/4 X 4 (Tekton 31250 or 11250)
5/16 X 4 (Tekton 31313 or 11313)
3/16 X 8 (Tekton 34188 or 14188)
1/4 X 8 (Tekton 34250 or 14250)
5/16 X 8 (Tekton 34313 or 14313)
phillips:
#2 X 1-1/2 (Tekton 30002 or 10002)
#0 X 4 (Tekton 31000 or 11000)
#1 X 4 (Tekton 31001 or 11001)
#2 X 4 (Tekton 31002 or 11002)
#3 X 4 (Tekton 31003 or 11003)
#1 X 8 (Tekton 34001 or 14001)
#2 X 8 (Tekton 34002 or 14002)
#3 X 8 (Tekton 34003 or 14003)
torx:
T10 X 4 (Tekton 31100 or 11100)
T15 X 4 (Tekton 31150 or 11150)
T20 X 4 (Tekton 31200 or 11200)
T25 X 4 (Tekton 31250 or 11250)
T27 X 4 (Tekton 31270 or 11270)
T30 X 4 (Tekton 31300 or 11300)
This tool organizer was designed to fit the first version of the 22-piece Tekton hard-handle screwdriver set. The 1/8, 3/16, P0, and P1 screwdrivers in this version have the same size handle. This organizer fits screwdrivers with chrome blades or black oxide blades. Model numbers include DRV40122, DRV42020, DRV40115, and DRV42012.
Printing the drawing at 100% scale can be an easy way to check if your tools will fit. Our drawings have multiple pages which can be printed on letter-size paper. Always change the printer setting from "fit" to 100%. If the border prints slightly too small, it is often due to this setting.
24 X 18 inches (inside width by inside depth)
Works in most drawers, needing no more than 2 inches of vertical clearance.
It is possible to trim the margins to fit a smaller drawer. Trimmed tool organizers are not returnable. The minimum recommended size is:
21-1/2 X 15-7/8 inches
Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.
We make these colors in smaller batches, but they are often in stock. Contact customer service to order.
Each FoamFit insert is designed for shadowing a specific brand and set of tools. These organizers are made from high-quality tool foam with pockets precision-cut on our CNC routers.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. The foam is resistant to most oils and fuels.