FoamFit Tools section divider

Foam Tool Organizer for
25 Craftsman Screwdriver Set #1

see all organizers for screwdrivers


25 Craftsman Screwdriver Set #1

Fits (6) slotted screwdrivers,
(6) Phillips screwdrivers,
(4) torx screwdrivers,
(1) pocket screwdriver,
(3) offset screwdrivers,
(1) square screwdriver, and (4) mini picks.

Accommodates 25 screwdrivers from the
25-piece set CMHT65046.


Drawer Size
22-1/4 X 14-1/2 inches


FoamFit Tools section divider


This foam tool organizer is made from closed-cell polyethylene tool foam. It has been precision CNC-cut to fit the following 25 Craftsman screwdrivers:

3/32 X 1-1/2
1/8 X 2-1/2 (CMHT65017)
3/16 X 4 (CMHT65021)
1/4 X 1-1/2 (CMHT65013)
1/4 X 4 (CMHT65014)
1/4 X 6 (CMHT65015)

P0 X 1-1/2
P0 X 2-1/2 (CMHT65000)
P1 X 3 (CMHT65002)
P2 X 1-1/2 (CMHT65003)
P2 X 4 (CMHT65004)
P2 X 6 (CMHT65005)

T10 X 3 (CMHT65035)
T15 X 3 (CMHT65036)
T20 X 3 (CMHT65037)
T25 X 4 (CMHT65038)

other screwdrivers:
(1) square #2 X 4 (CMHT65033)
(4) mini-picks
(3) offset screwdrivers
(1) pocket/keychain

This tool organizer was designed to fit the 25-Piece Craftsman screwdriver set CMHT65046.

This organizer is designed to fit a toolbox drawer with inner dimensions of:

22-1/4 X 14-1/2 inches
(inside width by inside length)

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.

Made in the USA!

Foam Organizer for 25 Craftsman screwdrivers

Note: tools are not included

FoamFit Tools section divider


Please verify this organizer fits your tools before placing an order.

  1. Download the drawing:
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site