FoamFit Tools section divider

Foam Tool Organizer for
15 Craftsman Metric Combination Wrenches, Fits Stanley non-USA Version

see all organizers for combination wrenches


15 Craftsman Metric Combination Wrenches, Fits Stanley non-USA Version

Fits raised-panel wrenches from 8 to 22 mm.

Accommodates the wrenches from the 15-pc Craftsman set CMMT12066.

Only fits Craftsman raised-panel wrenches made by Stanley Black & Decker and sold at Lowes (and a few other Craftsman dealers).

Does not fit wrenches sold by Sears.

Drawer Size
22-1/4 X 16-1/4 inches


FoamFit Tools section divider


This foam tool organizer is made from closed-cell polyethylene tool foam. It has been precision CNC-cut to fit the following 15 Craftsman wrenches:

8 (Craftsman CMMT42912)
9 (Craftsman CMMT42913)
10 (Craftsman CMMT42914)
11 (Craftsman CMMT42915)
12 (Craftsman CMMT42916)
13 (Craftsman CMMT42917)
14 (Craftsman CMMT42918)
15 (Craftsman CMMT42919)
16 (Craftsman CMMT42924)
17 (Craftsman CMMT42929)
18 (Craftsman CMMT42925)
19 (Craftsman CMMT42921)
20 (Craftsman CMMT42937)
21 (Craftsman CMMT42938)
22 (Craftsman CMMT42922)

This tool organizer was designed to fit the metric combination wrenches from the Craftsman 15-piece set CMMT12066. The pockets only fit raised-panel Craftsman wrenches made by Stanley Black & Decker after they acquired Craftsman. Does not fit wrenches sold by Sears.

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.

Made in the USA!

Foam Organizer for Craftsman Raised-Panel Metric Combination Wrenches from the 15-Piece Wrench Set

note: tools are not included

Drawer Size

This organizer is designed to fit a toolbox drawer with inner dimensions of:

22-1/4 X 16-1/4 inches (inside width by inside depth)

It is possible to trim this organizer to fit a smaller drawer. The minimum recommended size is 20-1/8 X 14-1/4 inches. Note that trimmed organizers are not returnable. Also, contact customer service to order an organizer trimmed or made with a different sheet size.


Please verify this organizer fits your tools before placing an order.

  1. Download the drawing:
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site