FoamFit Tools section divider

Foam Tool Organizer for
15 Craftsman Inch Combination Wrenches, Fits Stanley non-USA Version

see all organizers for combination wrenches


15 Craftsman Inch Combination Wrenches, Fits Stanley non-USA Version

Fits raised-panel wrenches from 1/4 to 1-1/16.

Accommodates the wrenches from the 15-pc Craftsman set CMMT12067.

Only fits Craftsman raised-panel wrenches made by Stanley Black & Decker and sold at Lowes (and a few other Craftsman dealers).

Does not fit wrenches sold by Sears.

Drawer Size
22-1/4 X 16-1/4 inches


FoamFit Tools section divider


1/4 (Craftsman CMMT44699)
5/16 (Craftsman CMMT44691)
11/32 (Craftsman CMMT44692)
3/8 (Craftsman CMMT44693)
7/16 (Craftsman CMMT44694)
1/2 (Craftsman CMMT44695)
9/16 (Craftsman CMMT44696)
5/8 (Craftsman CMMT44697)
11/16 (Craftsman CMMT44698)
3/4 (Craftsman CMMT44701)
13/16 (Craftsman CMMT44702)
7/8 (Craftsman CMMT44703)
15/16 (Craftsman CMMT44704)
1 (Craftsman CMMT44705)
1-1/16 (Craftsman CMMT44706)

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.

Made in the USA!

Foam Organizer for Craftsman Raised-Panel Inch Combination Wrenches from the 15-Piece Wrench Set

note: tools are not included

Tool Requirements

This tool organizer was designed to fit the inch combination wrenches from the Craftsman 15-piece set CMMT12067. The pockets only fit raised-panel Craftsman wrenches made by Stanley Black & Decker after they acquired Craftsman. Does not fit wrenches sold by Sears.

Possible Modifications

Minimum trimmable size:

21-3/8 X 14-1/4 inches

Note: Trimmed organizers are not returnable.

Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.

Colors by special request:

black/yellow, black/green, black/gray

contact customer service to order this organizer in a special color.


Please verify this organizer fits your tools before placing an order.

  1. Download the drawing:
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site