FoamFit Tools section divider

Foam Tool Organizer for
23 Wright Inch and Metric Combination Wrenches

see all organizers for premium tools

Overview

23 Wright Inch and Metric Combination Wrenches

Fits (11) inch wrenches from 1/4 through 7/8 and (12) metric wrenches from 8 to 19 mm.

May be trimmed to fit a variety of drawer sizes.

Fits satin-finish or full-polish wrenches.

Drawer Size
24 X 18 inches

$48.00



FoamFit Tools section divider

Details

This foam tool organizer is made from closed-cell polyethylene tool foam. It has been precision CNC-cut to fit the following 23 Wright wrenches:

inch sizes:
1/4 (Wright 1108 or 1208)
5/16 (Wright 1110 or 1210)
3/8 (Wright 1112 or 1212)
7/16 (Wright 1114 or 1214)
1/2 (Wright 1116 or 1216)
9/16 (Wright 1118 or 1218)
5/8 (Wright 1120 or 1220)
11/16 (Wright 1122 or 1222)
3/4 (Wright 1124 or 1224)
13/16 (Wright 1126 or 1226)
7/8 (Wright 1128 or 1228)

metric sizes:
8 (Wright 11-08mm or 12-08mm)
9 (Wright 11-09mm or 12-09mm)
10 (Wright 11-10mm or 12-10mm)
11 (Wright 11-11mm or 12-11mm)
12 (Wright 11-12mm or 12-12mm)
13 (Wright 11-13mm or 12-13mm)
14 (Wright 11-14mm or 12-14mm)
15 (Wright 11-15mm or 12-15mm)
16 (Wright 11-16mm or 12-16mm)
17 (Wright 11-17mm or 12-17mm)
18 (Wright 11-18mm or 12-18mm)
19 (Wright 11-19mm or 12-19mm)

This tool organizer fits the WrightGrip satin-finish or full-polish wrenches. It may be trimmed to fit a variety of drawer sizes. The minimum size is marked on the drawing (see link below).

This organizer is designed to fit a toolbox drawer with inner dimensions of:

24 X 18 inches
(inside width by inside length)

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.



Made in the USA!

Foam Organizer for 23 Wright Combination Wrenches

Note: tools are not included

FoamFit Tools section divider

Drawing

Please verify this organizer fits your tools before placing an order.

  1. Download the drawing: www.FoamFitTools.com/product/F-02796-R.pdf
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider