FoamFit Tools section divider

Foam Tool Organizer for
12 Craftsman Deep Offset Box Wrenches with 6 Open End Ignition Wrenches

see all organizers for specialty wrenches

Overview

12 Craftsman Deep Offset Box Wrenches with 6 Open End Ignition Wrenches

Fits (5) inch deep offset box wrenches, (7) metric deep offset box wrenches, (3) inch open end ignition wrenches, and (3) metric open end ignition wrenches.

Accommodates the deep offset box wrenches and open-end ignition wrenches from the Craftsman 903-pc set 21470.

Caution: Fits shorter version of 20 X 22 wrench. See note about wrench length.

Drawer Size
22-1/4 X 16-1/4 inches

$50.20



FoamFit Tools section divider

Details

This foam tool organizer is made from closed-cell polyethylene tool foam. It has been precision CNC-cut to fit the following 18 Craftsman wrenches:

inch deep offset box wrenches:
3/8 X 7/16 (Craftsman 44316)
1/2 X 9/16 (Craftsman 44317)
5/8 X 11/16 (Craftsman 44318)
3/4 X 7/8 (Craftsman 44319)
13/16 X 15/16 (Craftsman 44320)

inch open-end ignition wrenches:
11/32 (Craftsman 43106)
3/8 (Craftsman 43107)
7/16 (Craftsman 43108)

metric deep offset box wrenches:
10 X 11 (Craftsman 44360)
12 X 14 (Craftsman 44361)
13 X 15 (Craftsman 44362)
16 X 18 (Craftsman 44364)
17 X 19 (Craftsman 44366)
20 X 22 (Craftsman 44367)
21 X 23 (Craftsman 44368)

metric open-end ignition wrenches:
6 (Craftsman 44552)
10 (Craftsman 44556)
11 (Craftsman 44557)

Note about wrench length: Some of the 903 piece sets produced under Craftsman model number 21470 have a longer 20 X 22 deep offset box wrench that will not fit in this organizer. Download the drawing below to check the fit, or measure the 20 X 22 box wrench in your set. The length of the 20 X 22 wrench should be approximately 11-7/8 inches long.

This tool organizer was designed to fit the deep offset box wrenches and open-end ignition wrenches from the Craftsman 903-pc set 21470. The pockets are sized to fit tools that don't have "USA" markings.

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.



Made in the USA!

Foam Organizer for 12 Craftsman Deep Offset Box Wrenches and 6 Open End Ignition Wrenches

note: tools are not included

Drawer Size

This organizer is designed to fit a toolbox drawer with inner dimensions of:

22-1/4 X 16-1/4 inches (inside width by inside depth)

It is possible to trim this organizer to fit a smaller drawer. The minimum recommended size is 22 X 14-7/16 inches. Note that trimmed organizers are not returnable. Also, contact customer service to order an organizer trimmed or made with a different sheet size.

Drawing

Please verify this organizer fits your tools before placing an order.

  1. Download the drawing: www.FoamFitTools.com/product/F1M-02002.pdf
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site