FoamFit Tools section divider

Foam Tool Organizer for
18 Wright Ratchets, Extensions, and Drive Accessories with 2 Eklind Hex Key Sets

see all organizers for premium tools


18 Wright Ratchets, Extensions, and Drive Accessories with 2 Eklind Hex Key Sets

Fits (3) Wright ratchets, (1) flex handle, (1) spinner handle, (8) extensions, (4) adapters, (1) universal, and (2) Eklind ball-end hex key sets.

May be trimmed to fit a variety of drawer sizes.

Drawer Size
24 X 18 inches


FoamFit Tools section divider


This foam tool organizer is made from closed-cell polyethylene tool foam. It has been precision CNC-cut to fit the following 18 Wright drive tools and 2 Eklind hex key sets:

1/4-drive ratchet (Wright 2492)
1/4-drive spinner handle (Wright 2442)
3/8-drive ratchet (Wright 3490)
1/2-drive ratchet (Wright 4490)
1/2-drive flex head, 18 inch (Wright 4435)
extension, 1/4 X 2 (Wright 2402)
extension, 1/4 X 4 (Wright 2404)
extension, 1/4 X 6 (Wright 2406)
extension, 3/8 X 3 (Wright 3403)
extension, 3/8 X 6 (Wright 3405)
extension, 3/8 X 8 (Wright 3408)
extension, 1/2 X 5 (Wright 4405)
extension, 1/2 X 10 (Wright 4410)
3/8-drive universal (Wright 3475)
adapter, 1/4 to 3/8 (Wright 2453)
adapter, 3/8 to 1/4 (Wright 3452)
adapter, 3/8 to 1/2 (Wright 3454)
adapter, 1/2 to 3/8 (Wright 4453)
13-pc inch ball hex key set (Eklind 13213)
9-pc metric ball hex key set (Eklind 13609)

This tool organizer insert may be trimmed to fit a variety of drawer sizes. The minimum size is marked on the drawing (see link below).

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.

Made in the USA!

Foam Organizer for 18 Wright Ratchets and Drive Tools with 2 Eklind Hex Key Sets

note: tools are not included

Drawer Size

This organizer is designed to fit a toolbox drawer with inner dimensions of:

24 X 18 inches (inside width by inside depth)

It is possible to trim this organizer to fit a smaller drawer. The minimum recommended size is 21 X 13-5/16 inches. Note that trimmed organizers are not returnable. Also, contact customer service to order an organizer trimmed or made with a different sheet size.


Please verify this organizer fits your tools before placing an order.

  1. Download the drawing:
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site