FoamFit Tools section divider

Foam Tool Organizer for
28 Snap-on Combination Wrenches

see all organizers for Snap-on tools

Overview

28 Snap-on Combination Wrenches

Fits (13) full-polish wrenches from 5/16 to 1 inch, and (15) full-polish wrenches from 8 to 22 mm.

Fits wrenches with the standard handle length.

New!

Drawer Size
30-1/2 X 21-7/8 inches

$77.50



FoamFit Tools section divider

Details

This foam tool organizer is made from closed-cell polyethylene tool foam. It has been precision CNC-cut to fit the following 28 Snap-on wrenches:

inch combination wrench sizes:
5/16 (Snap-on OEX10B)
11/32 (Snap-on OEX11B)
3/8 (Snap-on OEX12B)
7/16 (Snap-on OEX14B)
1/2 (Snap-on OEX16B)
9/16 (Snap-on OEX18B)
5/8 (Snap-on OEX20B)
11/16 (Snap-on OEX22B)
3/4 (Snap-on OEX24B)
13/16 (Snap-on OEX26B)
7/8 (Snap-on OEX28B)
15/16 (Snap-on OEX30B)
1 (Snap-on OEX32B)

metric combination wrench sizes:
8 (Snap-on OEXM80B)
9 (Snap-on OEXM90B)
10 (Snap-on OEXM100B)
11 (Snap-on OEXM110B)
12 (Snap-on OEXM120B)
13 (Snap-on OEXM130B)
14 (Snap-on OEXM140B)
15 (Snap-on OEXM150B)
16 (Snap-on OEXM160B)
17 (Snap-on OEXM170B)
18 (Snap-on OEXM180B)
19 (Snap-on OEXM190B)
20 (Snap-on OEXM200B)
21 (Snap-on OEXM210B)
22 (Snap-on OEXM220B)

This tool organizer was designed to fit full-polish, standard length Snap-on wrenches.

This organizer is designed to fit a toolbox drawer with inner dimensions of:

30-1/2 X 21-7/8 inches
(inside width by inside length)

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.



Made in the USA!

Foam

Note: tools are not included

FoamFit Tools section divider

Drawing

Please verify this organizer fits your tools before placing an order.

  1. Download the drawing: www.FoamFitTools.com/product/F1A-01481.pdf
  2. Print the pages of the drawing full size (page scaling = none).
  3. Assemble the pages and place the printed drawing in your toolbox drawer.
  4. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider