Fits (41) inch 1/4-drive sockets,
(23) metric 1/4-drive sockets,
(1) ratchet,
(3) extensions,
(1) swivel,
(1) adapter,
(1) magnetic handle,
(12) nut driver bits,
(4) slotted screwdrivers,
and (4) Phillips screwdrivers.
Accommodates the 1/4-drive sockets, drive tools, and screwdrivers from the Craftsman 348-piece set 49348.
Drawer Size
22-1/4 X 14-1/2 inches
$51.40
larger image
note: tools are not included
Precision CNC-cut to fit 64 Craftsman sockets and additional tools:
(11) 1/4-drive 6-point sizes from 5/32 to 9/16
(10) 1/4-drive 12-point sizes from 3/16 to 9/16
(10) 1/4-drive 6-point deep sizes from 3/16 to 9/16
(10) 1/4-drive 12-point deep sizes from 3/16 to 9/16
(12) 1/4-drive 6-point sizes from 4 to 14
(11) 1/4-drive 6-point deep sizes from 4 to 14
1/4-drive thin-profile ratchet (Craftsman 44994)
1-1/2-inch extension bar, 1/4-drive (Craftsman 43538)
3-inch extension bar, 1/4-drive (Craftsman 43539)
6-inch extension bar, 1/4-drive (Craftsman 43531)
1/4-drive to 3/8 socket adapter (Craftsman 04257)
1/4-drive universal joint (Craftsman 04280)
magnetic handle (Craftsman 43373)
(7) inch nut driver bits
(5) metric nut driver bits
1/4 X 1-1/2 screwdriver
1/8 X 4 screwdriver
3/16 X 4 screwdriver
1/4 X 6 screwdriver
P2 X 1-1/2 screwdriver
P0 X 2-1/2 screwdriver
P1 X 3 screwdriver
P2 X 4 screwdriver
This tool organizer was designed to fit the 1/4-drive sockets, screwdrivers, and additional tools from the Craftsman 348-piece set 49348. The pockets are sized to fit sockets and ratchets that don't have "U.S.A." markings.
Printing the drawing at 100% scale can be an easy way to check if your tools will fit. Our drawings have multiple pages which can be printed on letter-size paper. Always change the printer setting from "fit" to 100%. If the border prints slightly too small, it is often due to this setting.
22-1/4 X 14-1/2 inches (inside width by inside depth)
Works in most drawers, needing no more than 2 inches of vertical clearance.
It is possible to trim the margins to fit a smaller drawer. Trimmed tool organizers are not returnable. The minimum recommended size is:
21-1/2 X 14-1/4 inches
Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.
We make these colors in smaller batches, but they are often in stock. Contact customer service to order.
Each FoamFit insert is designed for shadowing a specific brand and set of tools. These organizers are made from high-quality tool foam with pockets precision-cut on our CNC routers.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. The foam is resistant to most oils and fuels.