FoamFit Tools section divider

Foam Tool Organizer for
22 Craftsman Full-Polish Stubby Wrenches, Fits non-USA Wrenches

see all organizers for specialty wrenches

Overview

22 Craftsman Full-Polish Stubby Wrenches, Fits non-USA Wrenches

Fits (11) full-polish inch,
and (11) full-polish metric stubby wrenches.

Accommodates the stubby wrenches from the Craftsman 48-piece set 41048 or 23731.

Drawer Size
22-1/4 X 16-1/4 inches

$50.20



FoamFit Tools section divider

Details

This foam tool organizer is made from closed-cell polyethylene tool foam. It has been precision CNC-cut to fit the following 22 Craftsman wrenches:

inch stubby combination wrench sizes:
3/8 (Craftsman 44103)
7/16 (Craftsman 44104)
1/2 (Craftsman 44105)
9/16 (Craftsman 44106)
5/8 (Craftsman 44107)
11/16 (Craftsman 44108)
3/4 (Craftsman 44109)
13/16 (Craftsman 44099)
7/8 (Craftsman 44100)
15/16 (Craftsman 44102)
1 (Craftsman 44110)

metric stubby combination wrench sizes:
10 (Craftsman 44113)
12 (Craftsman 44114)
13 (Craftsman 44115)
14 (Craftsman 44116)
15 (Craftsman 44117)
17 (Craftsman 44118)
18 (Craftsman 44119)
19 (Craftsman 44120)
20 (Craftsman 44122)
21 (Craftsman 44124)
22 (Craftsman 44130)

This tool organizer was designed to fit the stubby combination wrenches from the Craftsman 48-piece wrench set 41048 or 23731. The pockets only fit full-polish wrenches that don't have "USA" markings.

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.



Made in the USA!

Foam Organizer for Craftsman Full-Polish Stubby Wrenches from the 48-Piece Wrench Set

note: tools are not included

Drawer Size

This organizer is designed to fit a toolbox drawer with inner dimensions of:

22-1/4 X 16-1/4 inches (inside width by inside depth)

It is possible to trim this organizer to fit a smaller drawer. The minimum recommended size is 22 X 14 inches. Note that trimmed organizers are not returnable. Also, contact customer service to order an organizer trimmed or made with a different sheet size.

Drawing

Please verify this organizer fits your tools before placing an order.

  1. Download the drawing: www.FoamFitTools.com/product/F1M-01398.pdf
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site