FoamFit Tools section divider

Foam Tool Organizer for
5 Craftsman Hammers with Pry Bar and 8 Punches

see all organizers for hammers and punches

Overview

5 Craftsman Hammers with Pry Bar and 8 Punches

Fits (5) hammers,
(1) pry bar,
(7) punches,
and (1) chisel.

Drawer Size
22-1/4 X 14-1/2 inches

$46.30



FoamFit Tools section divider

Details

This foam tool organizer is made from closed-cell polyethylene tool foam. It has been precision CNC-cut to fit the following 5 Craftsman hammers and 9 additional tools:

8-oz ball pein hammer (Craftsman 38463)
16-oz ball pein hammer (Craftsman 38465)
12-oz plastic tip hammer (Craftsman 38292)
16-oz claw hammer (Craftsman 3821)
2-lb dead blow hammer (Craftsman 38394)
17 inch pry bar (Craftsman 43276)
1/16 X 4 pin punch (Craftsman 42881)
3/32 X 4 pin punch (Craftsman 42882)
1/8 X 4-1/2 pin punch (Craftsman 42883)
5/32 X 5 pin punch (Craftsman 42884)
3/8 X 4-1/2 center punch (Craftsman 42861)
3/8 X 4-1/2 prick punch (Craftsman 42841)
5/32 X 7 line up tool (Craftsman 42901)
1/2 X 5-3/4 cold chisel (Craftsman 42973)

The pin and alignment punches are available as Craftsman set 4285.

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.



Made in the USA!

Foam Organizer for 5 Craftsman Hammers, 1 Pry Bar, 7 Punches, and 1 Chisel

note: tools are not included

Drawer Size

This organizer is designed to fit a toolbox drawer with inner dimensions of:

22-1/4 X 14-1/2 inches (inside width by inside depth)

It is possible to trim this organizer to fit a smaller drawer. The minimum recommended size is 21-3/4 X 14-1/4 inches. Note that trimmed organizers are not returnable. Also, contact customer service to order an organizer trimmed or made with a different sheet size.

Drawing

Please verify this organizer fits your tools before placing an order.

  1. Download the drawing: www.FoamFitTools.com/product/F1M-01335.pdf
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site