Fits (73) inch sockets,
(66) metric sockets,
(17) hex bit sockets,
(16) Torx sockets,
and (7) screwdriver bit sockets.
Accommodates all 1/4 and 3/8-drive sockets from the 413-piece mechanics tool set 33413.
Recommended for 3 min drawer height.
Drawer Size
22-1/4 X 14-1/2 inches
$67.70
larger image
note: tools are not included
Precision CNC-cut to fit 179 Craftsman sockets:
(11) 1/4-drive 6-point sizes from 5/32 to 9/16
(12) 1/4-drive 6-point sizes from 4 to 14
(10) 1/4-drive 12-point sizes from 3/16 to 9/16
(10) 1/4-drive 6-point deep sizes from 3/16 to 9/16
(11) 1/4-drive 6-point deep sizes from 4 to 14
(5) 1/4-drive hex bit sizes from 3/16 to 3/8
(3) 1/4-drive Torx screwdriver bits from T15 to T25
(3) 1/4-drive external Torx sizes from E6 to E8
(13) 3/8-drive 6-point sizes from 1/4 to 1
(17) 3/8-drive 6-point sizes from 6 to 22
(5) 3/8-drive 8-point sizes from 1/4 to 1/2
(11) 3/8-drive 12-point sizes from 1/4 to 7/8
(15) 3/8-drive 12-point sizes from 6 to 19 plus 21
(11) 3/8-drive 6-point deep sizes from 3/8 to 1
(11) 3/8-drive 6-point deep sizes from 9 to 19
(6) 3/8-drive hex bit sizes from 5/32 to 3/8
(6) 3/8-drive hex bit sizes from 4 to 8 plus 10
(3) 3/8-drive slotted screwdriver bits from 7/32 to 3/8
(4) 3/8-drive Phillips screwdriver bits from P1 to P4
(6) 3/8-drive Torx screwdriver bits from T27 to T50
(4) 3/8-drive external Torx sizes from E10 to E16
(2) 3/8-drive spark plug sockets, 5/8 and 13/16
This tool organizer was designed to fit the 1/4 and 3/8-drive sockets from the Craftsman 413-piece set 33413. The pockets fit the newer sockets which do not have "U.S.A." markings.
Printing the drawing at 100% scale can be an easy way to check if your tools will fit. Our drawings have multiple pages which can be printed on letter-size paper. Always change the printer setting from "fit" to 100%. If the border prints slightly too small, it is often due to this setting.
22-1/4 X 14-1/2 inches (inside width by inside depth)
Recommended for a drawer with at least 3 inches of vertical clearance.
It is possible to trim the margins to fit a smaller drawer. Trimmed tool organizers are not returnable. The minimum recommended size is:
21-3/4 X 11-3/4 inches
Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.
We make these colors in smaller batches, but they are often in stock. Contact customer service to order.
Each FoamFit insert is designed for shadowing a specific brand and set of tools. These organizers are made from high-quality tool foam with pockets precision-cut on our CNC routers.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. The foam is resistant to most oils and fuels.