FoamFit Tools section divider

Foam Tool Organizer for
8 Craftsman Inch Stubby Wrenches and 4 Flare-Nut Wrenches, Fits non-USA Wrenches

see all organizers for specialty wrenches

Overview

8 Craftsman Inch Stubby Wrenches and 4 Flare-Nut Wrenches, Fits non-USA Wrenches

Fits (8) inch stubby combination wrenches,
and (4) inch flare-nut wrenches.

Note: this organizer fits the inch stubby and flare-nut wrenches from the newer version of the Craftsman 540-piece mechanics tool set (see Craftsman 35540).

Drawer Size
11-1/2 X 16-1/4 inches

$31.20



FoamFit Tools section divider

Details

This foam tool organizer is made from closed-cell polyethylene tool foam. It has been precision CNC-cut to fit the following 12 Craftsman wrenches:

inch stubby combination wrenches:
3/8 (Craftsman 44103)
7/16 (Craftsman 44104)
1/2 (Craftsman 44105)
9/16 (Craftsman 44106)
5/8 (Craftsman 44107)
11/16 (Craftsman 44108)
3/4 (Craftsman 44109)
13/16 (Craftsman 44099)

inch flare-nut wrenches:
3/8 X 7/16 (Craftsman 42091)
1/2 X 9/16 (Craftsman 42092)
5/8 X 11/16 (Craftsman 42093)
3/4 X 7/8 (Craftsman 42094)

This tool organizer was designed to fit the inch stubby and flare-nut wrenches from version 2 of the Craftsman 540-piece set (see Craftsman 35540). The pockets are sized to fit tools that don't have "USA" markings.

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.



Made in the USA!

Foam Organizer for Craftsman Inch Stubby and Flare-Nut Wrenches from the 540-Piece Mechanics Tool Set

note: tools are not included

Drawer Size

This organizer is designed to fit a toolbox drawer with inner dimensions of:

11-1/2 X 16-1/4 inches (inside width by inside depth)

It is possible to trim this organizer to fit a smaller drawer. The minimum recommended size is 11-1/4 X 15-3/4 inches. Note that trimmed organizers are not returnable. Also, contact customer service to order an organizer trimmed or made with a different sheet size.

Drawing

Please verify this organizer fits your tools before placing an order.

  1. Download the drawing: www.FoamFitTools.com/product/F1S-01054.pdf
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site