FoamFit Tools section divider

Foam Tool Organizer for
16 Craftsman Stubby and 9 Flare-Nut Wrenches, Fits non-USA Wrenches

see all organizers for specialty wrenches


16 Craftsman Stubby and 9 Flare-Nut Wrenches, Fits non-USA Wrenches

Fits (8) inch stubby combination wrenches,
(4) inch flare-nut wrenches,
(8) metric stubby combination wrenches,
and (5) metric flare-nut wrenches.

Note: this organizer fits the stubby and flare-nut wrenches from the newer version of the Craftsman 540-piece mechanics tool set (see Craftsman 35540).

Drawer Size
22-1/4 X 16-1/4 inches


FoamFit Tools section divider


inch stubby combination wrenches:
3/8 (Craftsman 44103)
7/16 (Craftsman 44104)
1/2 (Craftsman 44105)
9/16 (Craftsman 44106)
5/8 (Craftsman 44107)
11/16 (Craftsman 44108)
3/4 (Craftsman 44109)
13/16 (Craftsman 44099)

inch flare-nut wrenches:
3/8 X 7/16 (Craftsman 42091)
1/2 X 9/16 (Craftsman 42092)
5/8 X 11/16 (Craftsman 42093)
3/4 X 7/8 (Craftsman 42094)

metric stubby combination wrenches:
10mm (Craftsman 44113)
12mm (Craftsman 44114)
13mm (Craftsman 44115)
14mm (Craftsman 44116)
15mm (Craftsman 44117)
17mm (Craftsman 44118)
18mm (Craftsman 44119)
19mm (Craftsman 44120)

metric flare-nut wrenches:
9 X 11 (Craftsman 42095)
10 X 12 (Craftsman 42096)
13 X 14 (Craftsman 42097)
15 X 17 (Craftsman 42098)
16 X 18 (Craftsman 42099)

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.

Made in the USA!

Foam Organizer for Craftsman Stubby and Flare-Nut Wrenches from the 540-Piece Mechanics Tool Set

note: tools are not included

Tool Requirements

This tool organizer was designed to fit the stubby and flare-nut wrenches from version 2 of the Craftsman 540-piece set (see Craftsman 35540). The pockets are sized to fit tools that don't have "USA" markings.

Possible Modifications

Minimum trimmable size:

21-3/4 X 16 inches

Note: Trimmed organizers are not returnable.

Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.

Colors by special request:

black/yellow, black/green, black/gray

contact customer service to order this organizer in a special color.


Please verify this organizer fits your tools before placing an order.

  1. Download the drawing:
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site