FoamFit Tools section divider

5 Nupla Hammer
KIT #158

Foam Organizer for 5 Nupla Hammers and 10 Mayhew Tools

larger image


Kits include both the tools and foam organizer.

This organizer is also available without tools: F-03680-R

FoamFit Tools section divider

Kit Description

5 Nupla Hammer Kit #158

This complete kit includes organizer insert F-03680-R, 5 Nupla Hammers, 1 Mayhew pry bar, and 9 Mayhew punches.

The tool organizer may be trimmed to fit a variety of drawer sizes. Please compare the minimum recommended size to your drawer size before ordering.

Detailed drawing: F-03680-R.pdf

made in the USA

Tool organizer made in USA. Tools made in USA.

1-Drawer Kit

Drawer Size
24 X 18 inches

$428.10 sale $344.20

Temporarily out of stock. Please contact us if you'd like to be notified when more are available.

FoamFit Tools section divider

Tools Included with Kit

This kit includes the following 15 Nupla and Mayhew tools:

12 oz ball pein (Nupla 21-012)
16 oz ball pein (Nupla 21-016)
16 oz soft face hammer (Nupla 11235, CBH-135)
20 oz rip claw hammer (Nupla 17-020)
2 lb dead blow (Nupla Power Drive 10025)
12 inch pry bar, 17 inch overall (Mayhew Dominator 60144)
center punch, 3/8 X 5 inch (Mayhew #415, size 3/8)
line-up punch, 5/32 X 9 (Mayhew 22011, #466, size 5/32)
cold chisel, 1/2 X 6 (Mayhew #70, size 1/2)
pin punch, 1/8 X 4-3/4 (Mayhew #413, size 1/8)
pin punch, 5/32 X 5 (Mayhew #413, size 5/32)
pin punch, 3/16 X 5-1/4 (Mayhew #413, size 3/16)
pin punch, 7/32 X 5-1/2 (Mayhew #413, size 7/32)
pin punch, 1/4 X 5-3/4 (Mayhew #413, size 1/4)
brass drift punch, 1/2 X 7 (Mayhew 25076)

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.


FoamFit Tools section divider

Drawer Requirements

The foam insert included with this kit measures 24 X 18 inches.

It is not possible to compress the foam because the tool pockets will also squeeze closed. The foam sheet can be trimmed with a sharp knife if necessary. Contact customer service if you'd like us to modify the sheet size to your measurements.

The minimum recommended size for trimming is 22 X 14-7/8 inches. This leaves a margin of approximately 1/4-inch. Trimmed organizers are not returnable.

FoamFit Tools section divider

Designer Notes

"This hammer kit was based on our original Nupla hammer kit. We switched from a claw hammer to a rip claw hammer. The rip claw hammer is larger and good for prying apart pallets and crates. We also added a small ball pein hammer, more pin punches, and a brass drift. These tools should come in handy working on cars, but would also be great for working on fixtures and machine tooling."

FoamFit Tools section divider

How Kits are Packaged and Shipped

After test fitting each kit, we remove the tools and seal them in a heavy-duty bag for shipping. We include a drawing to help place each tool back in the foam.

FoamFit Tools section divider

back to kits with hammers

back to kits with tools main page

view the full selection of tool organizers for Nupla and Mayhew tools

FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site