Home |
About |
FAQ |
Shipping Policies |
Extras and Deals |
Custom Options |
Contact Us
Foam Tool Organizer for
20 Tekton Screwdriver Set
Overview
20 Tekton Screwdriver Set
Fits (7) slotted, (7) phillips, and (6) torx screwdrivers.
Accommodates the high-torque black oxide screwdrivers from set DRV41216, torx set DHT91006, and two additional tools.
May be trimmed to fit a variety of drawer sizes.
Drawer Size
24 X 18 inches
$52.20
Details
This foam tool organizer is made from closed-cell polyethylene tool foam. It has been precision CNC-cut to fit the following 20 Tekton screwdrivers:
slotted:
1/4 X 1-1/2 (Tekton 26621)
1/8 X 4 (Tekton 26603)
3/16 X 4 (Tekton 26613)
5/16 X 4 (Tekton 26633)
1/4 X 4 (Tekton 26623)
3/16 X 8 (Tekton 26615)
1/4 X 8 (Tekton 26625)
phillips:
#2 X 1-1/2 (Tekton 26671)
#0 X 4 (Tekton 26653)
#1 X 4 (Tekton 26663)
#2 X 4 (Tekton 26673)
#3 X 4 (Tekton 26683)
#1 X 8 (Tekton 26665)
#2 X 8 (Tekton 26675)
torx:
T10 X 4 (Tekton 26801)
T15 X 4 (Tekton 26802)
T20 X 4 (Tekton 26803)
T25 X 4 (Tekton 26804)
T27 X 4 (Tekton 26805)
T30 X 4 (Tekton 26806)
This tool organizer was designed to fit the 20 Tekton screwdrivers from sets DRV41216 and DHT91006, plus individual screwdrivers 5/16 X 4 and #3 X 4.
Free shipping on all orders within the contiguous 48 US states.
Made in the USA!
note: tools are not included
Drawer Size
This organizer is designed to fit a toolbox drawer with inner dimensions of:
24 X 18 inches (inside width by inside depth)
It is possible to trim this organizer to fit a smaller drawer. The minimum recommended size is 21-3/4 X 16 inches. Note that trimmed organizers are not returnable. Also, contact customer service to order an organizer trimmed or made with a different sheet size.
Drawing
Please verify this organizer fits your tools before placing an order.
- Download the drawing: www.FoamFitTools.com/product/F-03576-R.pdf
- Print the pages of the drawing full size or 100% (not fit).
- Check that the printout is full size by measuring the border with a ruler.
- Assemble the pages and place the printed drawing in your toolbox drawer.
- Place the tools over the printed outlines. Visually check that each tool fits within its outline.
Additional Information
Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.
