FoamFit Tools section divider

Foam Tool Organizer for
14 Husky Inch Full-Polish Combination Wrenches

see all organizers for Husky tools


14 Husky Inch Full-Polish Combination Wrenches

Fits (14) inch combination wrenches from 1/4 to 1.

Accommodates the combination wrenches up to 1-inch from the Husky 432-pc set H432MTS.

Available Drawer Sizes:
20-3/8 X 15-11/16, $42.70
20-1/2 X 15-3/4, $43.00
21-1/2 X 15-3/4, $44.20
25-3/4 X 15-7/8, $52.50

FoamFit Tools section divider


This foam tool organizer is made from closed-cell polyethylene tool foam. It has been precision CNC-cut to fit the following 14 Husky wrenches:

inch combination wrench sizes:
1/4, 5/16, 11/32, 3/8, 7/16, 1/2, 9/16, 5/8, 11/16, 3/4, 13/16, 7/8, 15/16, 1

This tool organizer was designed to fit the inch combination wrenches up to the 1-inch size from the Husky 432-pc set H432MTS.

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.

Made in the USA!

Foam Organizer for 14 Inch Husky Full-Polish Combination Wrenches

note: tools are not included

Drawer Size

Four standard sizes are available (see below for measurements).

It is possible to trim these organizers to fit a smaller drawer. The minimum recommended size for these four layouts is 19-3/4 X 15 inches. Note that trimmed organizers are not returnable. Also, contact customer service to order an organizer trimmed or made with a different sheet size.


Please verify this organizer fits your tools before placing an order.

tool organizer drawings
foam size black/red
part number
part number
part number
20-3/8 X 15-11/16 inches F-02530-R1 F-02530-R2 F-02530-R3
20-1/2 X 15-3/4 inches F-02531-R1 F-02531-R2 F-02531-R3
21-1/2 X 15-3/4 inches F-02532-R1 F-02532-R2 F-02532-R3
25-3/4 X 15-7/8 inches F-02533-R1 F-02533-R2 F-02533-R3
  1. Download the drawing above that matches your drawer size.
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site