FoamFit Tools section divider

Foam Tool Organizer for
18 Craftsman Inch Combination Wrenches, Fits non-USA Wrenches

see all organizers for combination wrenches


18 Craftsman Inch Combination Wrenches, Fits non-USA Wrenches

Fits (18) raised-panel wrenches from 1/4 to 1-5/16.

Accommodates the inch combination wrenches from the Craftsman 43-pc wrench set 44048 or 63-pc wrench set 41232.

Caution: Recommended for a 3 inch or deeper drawer.

Drawer Size
22-1/4 X 16-1/4 inches


FoamFit Tools section divider


This foam tool organizer is made from closed-cell polyethylene tool foam. It has been precision CNC-cut to fit the following 18 Craftsman wrenches:

inch combination wrench sizes:
1/4 (Craftsman 44699)
5/16 (Craftsman 44691)
11/32 (Craftsman 44692)
3/8 (Craftsman 44693)
7/16 (Craftsman 44694)
1/2 (Craftsman 44695)
9/16 (Craftsman 44696)
5/8 (Craftsman 44697)
11/16 (Craftsman 44698)
3/4 (Craftsman 44701)
13/16 (Craftsman 44702)
7/8 (Craftsman 44703)
15/16 (Craftsman 44704)
1 (Craftsman 44705)
1-1/16 (Craftsman 44706)
1-1/8 (Craftsman 44707)
1-1/4 (Craftsman 44708)
1-5/16 (Craftsman 44709)

This tool organizer was designed to fit raised-panel wrenches from the Craftsman 43-pc wrench set 44048 or the 63-pc wrench set 41232. The pockets are sized to fit wrenches that don't have "USA" markings.

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.

Made in the USA!

Foam Organizer for Craftsman Raised-Panel Combination Wrenches from the 43 or 63-Piece Wrench Sets

note: tools are not included

Drawer Size

This organizer is designed to fit a toolbox drawer with inner dimensions of:

22-1/4 X 16-1/4 inches (inside width by inside depth)

It is possible to trim this organizer to fit a smaller drawer. The minimum recommended size is 21 X 12-1/4 inches. Note that trimmed organizers are not returnable. Also, contact customer service to order an organizer trimmed or made with a different sheet size.


Please verify this organizer fits your tools before placing an order.

  1. Download the drawing:
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site