Foam Tool Organizer for
21 Craftsman Stubby, Flare-Nut, and Obstruction Wrenches, Fits non-USA Wrenches

Overview

21 Craftsman Stubby, Flare-Nut, and Obstruction Wrenches, Fits non-USA Wrenches

Fits (6) inch stubby combination wrenches,
(4) inch flare-nut wrenches,
(1) obstruction wrench,
(6) metric stubby combination wrenches,
and (4) metric flare-nut wrenches.

Accommodates the stubby, obstruction, and flare-nut wrenches from the Craftsman 500-piece mechanics tool set 34500.

Drawer Size
22-1/4 X 16-1/4 inches

$53.40



Foam Organizer for 21 Craftsman Stubby, Flare-Nut, and Obstruction Wrenches, Fits non-USA Wrenches

larger image

Foam Organizer for 21 Craftsman Stubby, Flare-Nut, and Obstruction Wrenches, Fits non-USA Wrenches

larger image

note: tools are not included

Tool List

Precision CNC-cut to fit 21 Craftsman wrenches:

inch stubby combination wrenches:
7/16 (Craftsman 44104)
1/2 (Craftsman 44105)
9/16 (Craftsman 44106)
5/8 (Craftsman 44107)
11/16 (Craftsman 44108)
3/4 (Craftsman 44109)

inch flare-nut wrenches:
3/8 X 7/16 (Craftsman 42091)
1/2 X 9/16 (Craftsman 42092)
5/8 X 11/16 (Craftsman 42093)
3/4 X 7/8 (Craftsman 42094)

obstruction wrench:
9/16 X 5/8 (Craftsman 47463)

metric stubby combination wrenches:
10mm (Craftsman 44113)
12mm (Craftsman 44114)
13mm (Craftsman 44115)
14mm (Craftsman 44116)
15mm (Craftsman 44117)
17mm (Craftsman 44118)

metric flare-nut wrenches:
10 X 12 (Craftsman 42096)
13 X 14 (Craftsman 42097)
15 X 17 (Craftsman 42098)
16 X 18 (Craftsman 42099)

Tool Notes

This tool organizer was designed to fit the stubby, obstruction, and flare-nut wrenches from the Craftsman 500-piece set 34500. The pockets are sized to fit tools that don't have "USA" markings.

Drawing

Drawing F1M-01436.pdf

Printing the drawing at 100% scale can be an easy way to check if your tools will fit. Our drawings have multiple pages which can be printed on letter-size paper. Always change the printer setting from "fit" to 100%. If the border prints slightly too small, it is often due to this setting.

Drawer Size

22-1/4 X 16-1/4 inches (inside width by inside depth)

Drawer Height

Works in most drawers, needing no more than 2 inches of vertical clearance.

Minimum Trimmable Size

It is possible to trim the margins to fit a smaller drawer. Trimmed tool organizers are not returnable. The minimum recommended size is:

21-3/4 X 14-1/4 inches

Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.

Features and Benefits

Standard Colors

black over red color combination blue over yellow color combination black over blue color combination

Special Colors

We make these colors in smaller batches, but they are often in stock. Contact customer service to order.

black over yellow color combination black over green color combination black over gray color combination

Additional Information

Each FoamFit insert is designed for shadowing a specific brand and set of tools. These organizers are made from high-quality tool foam with pockets precision-cut on our CNC routers.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. The foam is resistant to most oils and fuels.

Free Shipping!

For orders within the contiguous 48 US states.

US flag

Made in the USA!