FoamFit Tools section divider

Foam Tool Organizer for
16 Craftsman Reversible Ratcheting Wrenches and 5 Tappet Wrenches, Fits non-USA Wrenches

see all organizers for Craftsman ratcheting wrenches

Overview

16 Craftsman Reversible Ratcheting Wrenches and 5 Tappet Wrenches, Fits non-USA Wrenches

Fits (8) reversible inch ratcheting wrenches, (8) reversible metric ratcheting wrenches, and (5) inch tappet wrenches.

Note: this organizer fits the ratcheting wrenches and tappet wrenches from the newer version of the Craftsman 540-piece mechanics tool set (see Craftsman 35540).

Drawer Size
22-1/4 X 14-1/2 inches

$39.00



FoamFit Tools section divider

Details

This foam tool organizer is made from closed-cell polyethylene tool foam. It has been precision CNC-cut to fit the following 21 Craftsman wrenches:

inch reversible ratcheting wrenches:
5/16 (Craftsman 42412)
3/8 (Craftsman 42413)
7/16 (Craftsman 42414)
1/2 (Craftsman 42415)
9/16 (Craftsman 42416)
5/8 (Craftsman 41417)
11/16 (Craftsman 41418)
3/4 (Craftsman 42419)

inch tappet wrenches:
3/8 X 7/16 (Craftsman 47467)
7/16 X 17/32 (Craftsman 04747)
1/2 X 9/16 (Craftsman 47474)
5/8 X 11/16 (Craftsman 47468)
3/4 X 7/8 (Craftsman 47465)

metric reversible ratcheting wrenches:
8mm (Craftsman 42420)
10mm (Craftsman 42421)
11mm (Craftsman 42422)
12mm (Craftsman 42423)
13mm (Craftsman 42424)
14mm (Craftsman 42425)
15mm (Craftsman 42426)
16mm (Craftsman 42427)

This tool organizer was designed to fit the reversible ratcheting wrenches and tappet wrenches from version 2 of the Craftsman 540-piece set (see Craftsman 35540). The pockets are sized to fit tools that don't have "USA" markings.

This organizer is designed to fit a standard Craftsman toolbox drawer with inner dimensions of:

22-1/4 X 14-1/2 inches
(inside width by inside length)

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.



Made in the USA!

Foam

Note: tools are not included

FoamFit Tools section divider

Drawing

Please verify this organizer fits your tools before placing an order.

  1. Download the drawing: www.FoamFitTools.com/product/F1M-01049.pdf
  2. Print the pages of the drawing full size (page scaling = none).
  3. Assemble the pages and place the printed drawing in your toolbox drawer.
  4. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider