FoamFit Tools section divider

Foam Tool Organizer for
19 Craftsman Inch and Metric Box Wrenches, Fits non-USA Version 2

see all organizers for Craftsman specialty wrenches

Overview

19 Craftsman Inch and Metric Box Wrenches, Fits non-USA Version 2

Fits (9) inch box wrenches,
(9) metric box wrenches,
and (1) inch obstruction wrench.

Note: this organizer fits all the box wrenches from version 2 of the Craftsman 540-piece mechanics tool set (see Craftsman 35540).

Caution: see note about wrench length.

Drawer Size
22-1/4 X 16-1/4 inches

$40.00



FoamFit Tools section divider

Details

This foam tool organizer is made from closed-cell polyethylene tool foam. It has been precision CNC-cut to fit the following 19 Craftsman box wrenches:

inch wrenches: 1/4 X 5/16, 3/8 X 7/16, 7/16 X 1/2, 1/2 X 9/16, 9/16 X 5/8, 5/8 X 3/4, 11/16 X 13/16, 3/4 X 7/8, 15/16 X 1

obstruction wrench: 9/16 X 5/8

metric wrenches: 6 X 8, 7 X 9, 10 X 11, 12 X 14, 13 X 15, 16 X 18, 17 X 19, 20 X 22, 21 X 23

Note about wrench length:
Some of the 540-piece sets produced under Craftsman model number 35540 have a longer 3/8 X 7/16 box wrench that will not fit in this organizer. Download the drawing below to check the fit, or measure the 3/8 X 7/16 box wrench in your set. The length of the 3/8 X 7/16 wrench should be approximately 7-3/4 inches long.

This tool organizer was designed to fit the box wrenches from version 2 of the Craftsman 540-piece set (see Craftsman 35540). The pockets are sized to fit tools that don't have "USA" markings.

This organizer is designed to fit a standard Craftsman toolbox drawer with inner dimensions of:

22-1/4 X 16-1/4 inches
(inside width by inside length)

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.



Made in the USA!

Foam

Note: tools are not included

FoamFit Tools section divider

Drawing

Please verify this organizer fits your tools before placing an order.

  1. Download the drawing: www.FoamFitTools.com/product/F1M-01046.pdf
  2. Print the pages of the drawing full size (page scaling = none).
  3. Assemble the pages and place the printed drawing in your toolbox drawer.
  4. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider